Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not take too lightly the forklift at work. If the operation is not good, there will be severe mishaps in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and hangs on the roadside shelf, which almost creates an accident.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was crushed.
Forklift procedure ought to take note of these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the chauffeur should first validate that the load is secure and dependable.
4. The start has to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work site or while driving, be careful that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal needs to be issued first. High-speed sharp turns are banned. High-speed doglegs will cause the car to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop Electric Forklift Truck for Warehouse location. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks need to be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs must be established to advise surrounding pedestrians. .
3. In the process of loading Stand-on Electric Pallet Stacker and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer should not touch various other items or objects. The load should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the tons is decreased to allow for simple positioning of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should unload the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Running up and down the incline ought to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the car needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844